NSE6_FWF-6.4 Online Practice Questions and Answers

Which factor is the best indicator of wireless client connection quality?

A. Downstream link rate, the connection rate for the AP to the client

B. The receive signal strength (RSS) of the client at the AP

C. Upstream link rate, the connection rate for the client to the AP

D. The channel utilization of the channel the client is using

Refer to the exhibits. Exhibit A.

Exhibit B.

Exhibit C.

A wireless network has been installed in a small office building and is being used by a business to connect its wireless clients. The network is used for multiple purposes, including corporate access, guest access, and connecting point-of-sale and IoТ devices.

Users connecting to the guest network located in the reception area are reporting slow performance. The network administrator is reviewing the information shown in the exhibits as part of the ongoing investigation of the problem. They show the profile used for the AP and the controller RF analysis output together with a screenshot of the GUI showing a summary of the AP and its neighboring APs.

To improve performance for the users connecting to the guest network in this area, which configuration change is most likely to improve performance?

A. Increase the transmission power of the AP radios

B. Enable frequency handoff on the AP to band steer clients

C. Reduce the number of wireless networks being broadcast by the AP

D. Install another AP in the reception area to improve available bandwidth

Which two phases are part of the process to plan a wireless design project? (Choose two.)

A. Project information phase

B. Hardware selection phase

C. Site survey phase

D. Installation phase

When enabling security fabric on the FortiGate interface to manage FortiAPs, which two types of communication channels are established between FortiGate and FortiAPs? (Choose two.)

A. Control channels

B. Security channels

C. FortLink channels

D. Data channels

Part of the location service registration process is to link FortiAPs in FortiPresence.

Which two management services can configure the discovered AP registration information from the FortiPresence cloud? (Choose two.)

A. AP Manager

B. FortiAP Cloud

C. FortiSwitch

D. FortiGate

Which two configurations are compatible for Wireless Single Sign-On (WSSO)? (Choose two.)

A. A VAP configured for captive portal authentication

B. A VAP configured for WPA2 or 3 Enterprise

C. A VAP configured to authenticate locally on FortiGate

D. A VAP configured to authenticate using a radius server

Refer to the exhibit.

What does the asterisk (*) symbol beside the channel mean?

A. Indicates channels that can be used only when Radio Resource Provisioning is enabled

B. Indicates channels that cannot be used because of regulatory channel restrictions

C. Indicates channels that will be scanned by the Wireless Intrusion Detection System (WIDS)

D. Indicates channels that are subject to dynamic frequency selection (DFS) regulations

Refer to the exhibit.

If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?

A. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility

B. Areas with the signal strength weaker than -68 dB are cut out of the map

C. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor

D. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.

Which statement is correct about security profiles on FortiAP devices?

A. Security profiles on FortiAP devices can use FortiGate subscription to inspect the traffic

B. Only bridge mode SSIDs can apply the security profiles

C. Disable DTLS on FortiAP

D. FortiGate performs inspection the wireless traffic

How can you find upstream and downstream link rates of a wireless client using FortiGate?

A. On the FortiAP CLI, using the cw_diag ksta command

B. On the FortiAP CLI, using the cw_diag -d sta command

C. On the FortiGate GUI, using the WiFi Client monitor

D. On the FortiGate CLI, using the diag wireless-controller wlac -d Sta command