NS0-506 Online Practice Questions and Answers

On a FAS8040, which port is used for FCoE connections?

A. e0M

B. e0P

C. 0a

D. e0h

Hosts and switches are connected to a FAS8040. Multiple FC-enabled SVMs have been created, and LUNs have been mapped to multiple hosts. During failover testing, one of the hosts lost connectivity to its LUNs.

What needs to be examined?

A. FAS8040 ALUA configuration

B. host multipath settings

C. xhost iSCSI timeout values

D. switch NPIV settings

Which three environmental or physical requirements need to be met when designing a SAN solution? (Choose three.)

A. rack space

B. cooling

C. clustered Data ONTAP version

D. IOPS

E. power

You have a large, heterogeneous SAN environment. You are asked to gather information for all hosts, HBAs, switches, and storage. You are also told that you must collect this information over network protocols without agents.

Which two NetApp tools allow you to perform this task? (Choose two.)

A. OnCommand Insight

B. OnCommand Report

C. OnCommand Unified Manager

D. nSANity

Exhibit

cl01::>igroup show -vserver svm1 VserverIgroup Protocol OS Type Initiators svm1 esx_cluster mixed vmware

20:00:00:25:b5:11:a0:01,

20:00:00:25:b5:11:b0:01,

iqn.1998-01.com.vmware:esx02

cl01::>

A customer is provisioning storage for two ESXi hosts using FCoE with CNA adapters. The customer mapped the LUN to the igroup shown in the exhibit. After scanning for new devices, the LUN is only seen by one of the ESXi hosts.

What caused the problem?

A. One of the hosts is added in the igroip via iSCSI IQN.

B. The igroup protocol needs to be configured as FCP.

C. The switch zoning configuration does not include the correct initiators.

D. The LIFs are not on their home ports.

You are creating a logical diagram for an FCP SAN solution.

You need to show connectivity between which three sets of components? (Choose three.)

A. management port and ACP cabling

B. inter-cluster network ports and hosts

C. hosts and FCP switches

D. hosts and FCoE switches

E. FCP switches and storage controller

A customer has a 4-node cluster and wants to use iSCSI for LUN traffic. Which license needs to be installed on the nodes?

A. iSCSI

B. SnapRestore

C. CIFS

D. FC

Which command enables the FC protocol on clustered Data ONTAP?

A. vserverfpolicy enable -vserver -policy name -sequence number

B. vserverfcp create -vserver -status -adain up

C. node run node fcadmincongig -e

D. vserveriscsi create-vserver -target -alias

You want to verify that a host will be able to see the storage. A LUN is mapped to an igroup for the host, and both the host and storage are connected to FC switches.

Which command will provide the path status information from the switch?

A. configure

B. cfgshow

C. fcping

D. zoneshow

Exhibit

cl01::> net int show -vserver svm1 (network interface show) Logical Status Network Current Current Is Vserver Interface Admin/Oper Address/Mask Node Port Home

svm1 fc_lif1 up/up 20:0b:00:a0:98:4e:ba:14 cl01-01 3a true fc_lif2 up/up 20:0c:00:a0:98:4e:ba:14 cl01-02 3a true lif1 up/up 172.16.21.31/24 cl01-01 a0a true

lif2 up/up 172.16.21.32/24 cl01-02 a0a true 4 entries were displayed. cl01::>

Referring to the exhibit, a customer needs to move LIF "fc_lif1" to a new port.

Which three actions must be performed to accomplish this task? (Choose three.)

A. Remove LIF from the existing portset.

B. Quiesce all hosts accessing LUNs over the LIF.

C. Take the LIF offline.

D. Update the switch zone to include the new WWPN.

E. Move the LIF to a new home port using the network interfacemodify command.