NS0-184 Online Practice Questions and Answers

After completing the installation of an AFF A800 ONTAP AI cluster, you are asked which contacts are available for additional help in obtaining immediate assistance in solving P1 issues.

In this scenario, what do you tell the customer?

A. Contact NetApp Support using chat.

B. Use Guided Problem Solving.

C. Contact NetApp Support by telephone.

D. Use the NetApp KB TV channel.

You need to install a cluster with a FAS2720 HA pair and a FAS8300 HA pair.

Which NetApp tool will verify which cluster interconnect switches support this configuration?

A. Active IQ Config Advisor

B. Interoperability Matrix Tool (IMT)

C. Hardware Universe (HWU)

D. mysupport.netapp.com site

You are planning to install a new ONTAP 9.7 All SAN Array (ASA) into your existing data center.

In this scenario, which cluster configuration is allowed with ASA controllers?

A. Add the ASA controllers to an existing 4-node cluster with NAS licenses.

B. ASA controllers can only be added to clusters that have existing SAN licenses.

C. ASA controllers can only be installed as a standalone HA pair.

D. Add the ASA controllers to an existing 10-node cluster.

You are adding new controllers to an existing cluster. As part of the upgrade process, you have updated the BES-53248 cluster switches.

In this scenario. Which two commands would you use to verify a healthy cluster after the upgrade? (Choose two.)

A. network port show -ipspace Cluster

B. network interface show -vserver Cluster

C. network device-discovery show -protocol cdp

D. network interface show -vserver Cluster -fields auto-revert

You are installing a new ONTAP 9.7 cluster by following the installation and setup poster. You are ready to complete the initial cluster setup. You have connected your laptop to the management switch. However, when browsing the network, you are unable to discover the ONTAP controllers.

Which statement explains this behavior?

A. You do not have network discovery enabled.

B. You do not have a static IP address.

C. You do not have IPv6 configuration set.

D. You do not have a default gateway set.

While installing a new AFF A400 HA pair, you are unable to add an NTP server from another subnet. You are able to ping the NTP server from the new cluster.

In this scenario, what are two causes of this problem? (Choose two.)

A. The admin SVM has the wrong gateway.

B. A firewall is blocking port 123.

C. The time skew is too great.

D. The cluster management LIF needs to be in a different IPspace.

You have just racked a new 6-node switched cluster with ONTAP 9.7. You need to configure the cluster switches.

In this scenario, which two elements would be used to complete the configuration? (Choose two.)

A. SFP+ port

B. rlogin

C. SSH

D. serial port

You are installing a new FAS2750 cluster with 24 HDDs for a customer to run a NAS workload. The customer requests that the HA pair have only a single aggregate that is located on Node 1. Maximum capacity is required.

Which action must be performed to ensure that the customer's requests are satisfied?

A. Perform a takeover of Node 2 to ensure that it does not run.

B. Assign all data LIFs to Node 1.

C. Assign all the partitioned disks from Node 2 to Node 1, and create a single aggregate.

D. Assign all the data partitions from Node 2 to Node 1, and create a single aggregate.

You are asked to add a new HA pair to an existing 2-node switchless AFF A220 cluster. You must first convert to a 2-node switched cluster using Broadcom BES-53248 cluster switches.

Which two conditions must be fulfilled before you start the migration? (Choose two.)

A. All cluster LIFs must be in the up state and on their home ports.

B. The "Enabled Switchless Cluster" option must be manually set to "false".

C. All cluster LIFs must have an MTU size of 1500.

D. The 2-node switchless configuration must be properly set up and functioning.

You are installing a new AFF A400 cluster and need to access the cluster management LIF from a remote subnet with the fully qualified domain name (FQDN) a400.lab.netapp.com.

In this scenario, which two network components must be configured to log in to ONTAP System Manager from the remote subnet? (Choose two.)

A. route

B. NTP

C. DNS

D. VLAN