NS0-183 Online Practice Questions and Answers

What should you do to change the data protocol of a LIF?

A. Delete and re-recreate the LIF.

B. Add the new data protocol to the LIF.

C. Put the LIF in another broadcast domain.

D. Shut down the assigned port.

You are preparing for the installation of a new 2-node cluster with ONTAP 9.7 using NL-SAS drives. Your customer wants to use the cluster exclusively with FlexGroups.

In this scenario, which two statements are correct? (Choose two.)

A. All NL-SAS drives are assigned only to one of the nodes.

B. A NAS protocol is licensed on both nodes.

C. A SAN protocol is licensed on both nodes.

D. All NL-SAS drives are divided evenly across both nodes.

Click the Exhibit button.

You plan to install a new ONTAP cluster at a customer site by using the new ONTAP System Manager 9.7 GUI.

Referring to the exhibit, what must you do before you provision initial storage?

A. Configure cluster LIFs.

B. Configure protocols.

C. Configure a remote tier.

D. Configure aggregates.

You are installing a new ONTAP 9.7 cluster by following the installation and setup poster. You are ready to complete the initial cluster setup. You have connected your laptop to the management switch. However, when browsing the network, you are unable to discover the ONTAP controllers.

Which statement explains this behavior?

A. You do not have network discovery enabled.

B. You do not have a static IP address.

C. You do not have IPv6 configuration set.

D. You do not have a default gateway set.

While installing a new AFF A400 HA pair, you are unable to add an NTP server from another subnet. You are able to ping the NTP server from the new cluster.

In this scenario, what are two causes of this problem? (Choose two.)

A. The admin SVM has the wrong gateway.

B. A firewall is blocking port 123.

C. The time skew is too great.

D. The cluster management LIF needs to be in a different IPspace.

Click the Exhibit button.

You are reviewing the setup of a recently installed FAS9000 switched cluster. As shown in the exhibit, the cluster interconnects are connected to a pair of Cisco Nexus 3132Q-V 40 Gb ports.

For a high availability, which ports should swap Ethernet cables?

A. Swap node1:e8a and node2:e4a.

B. Swap node1:e4a and node1:e8a.

C. Swap node2:e4a and node2:e8a.

D. Swap node1:e4a and node2:e4b.

You are installing a new FAS2750 cluster with 24 HDDs for a customer to run a NAS workload. The customer requests that the HA pair have only a single aggregate that is located on Node 1. Maximum capacity is required.

Which action must be performed to ensure that the customer's requests are satisfied?

A. Perform a takeover of Node 2 to ensure that it does not run.

B. Assign all data LIFs to Node 1.

C. Assign all the partitioned disks from Node 2 to Node 1, and create a single aggregate.

D. Assign all the data partitions from Node 2 to Node 1, and create a single aggregate.

You install a 4-node cluster with an AFF A400 HA pair and a FAS8300 HA pair. After setup, you are asked to review the audit logs on each controller from a Web browser.

In this scenario, which method provides access to the logs from a Web browser?

A. ACP

B. ADP

C. DNS

D. SPI

You have an AFF All SAN Array (ASA) cluster that is running ONTAP 9.7. The cluster is configured for Active Directory domain controller access using a domain tunnel.

In this scenario, which two licenses are enabled on the cluster? (Choose two.)

A. iSCSI

B. CIFS

C. NVMe

D. FCP

Click the Exhibit button.

A customer has two Cisco 40GbE data switches. They want to connect the switches to an AFF A400 HA pair. The switches and the AFF A400 are approximately seven meters apart.

Referring to the exhibit, which two supported actions would allow you to accomplish this task? (Choose two.)

A. Relocate the switches or the AFF A400 so that the distance is less than five meters.

B. Install 10 meter NetApp supported copper cables.

C. Change the requirement for Ethernet cables.

D. Change the requirement for optical cables.