An administrator has a VM that consumes large amounts of storage and has the following characteristics:
1.
Create large / sequential writes
2.
Data must be kept for years
3.
Data is normally only accessed at the end of the year to run report The administrator decides to use Erasure Coding to save space. Which feature should the administrator utilize to save space for this VM?
A. Inline Compression
B. Flash Mode
C. Cache Dedup
D. Post-Process Compression
An administrator needs to deploy an application with a large amount of data connected via Nutanix Volumes. Which two actions should the administrator take when designing the Volume Group? (Choose two.)
A. Use multiple subnets for iSCSI traffic
B. Enable RSS (Receive Side Scaling)
C. Enable thick provisioning on the Volume Group(s)
D. Distribute workload across multiple virtual disks
An administrator is updating disk firmware using LCM and receives the following message:
"there have been 10 or more cluster services restarts within 15 minutes in the Controller VM"
The message appears as each drive is upgraded.
What is the reason this message is being generated?
A. A node has been rebalanced
B. A drive has been reformatted
C. A node has been rebooted
D. A drive has been ejected
An administrator needs to forecast infrastructure requirements for a new program and its associated applications. Prior to the projected start of the new program, all existing applications will be decommissioned. How should the administrator perform this task?
A. Check the Disregard Existing Workloads radio button in the Runway scenario.
B. Check the Disregard Existing Nodes radio button in the Runway scenario.
C. Add up the recovered workloads and manually remove from the Runway configuration.
D. Power down the workloads during a maintenance window and run the Capacity Runway.
An administrator configures authentication in Prism Central (PC) for the NTNX-Admins group. Users report that they are unable to log in. The administrator confirms that the Active Directory (AD) settings in PC are correct. Which condition could result in this behavior?
A. A role mapping needs to be associated with the AD group.
B. The users must be added to the Domain Admins AD group.
C. The Local authentication type must also be selected in PC.
D. A client chap certificate must also be added in PC.
A customer has a primary datacenter with 12 Nutanix blocks distributed across three racks. The customer wants to achieve the most resiliency possible. They also have a datacenter in a branch office that is 400 kilometers away from the primary datacenter.
Which two solutions should be used? (Choose two.)
A. Time Stream to a remote site
B. Async DR to a remote site
C. Rack awareness
D. Block awareness
A customer has two mission-critical applications and needs to have them backed up to a remote location. The remote location is connected using a leased line and has an average latency of 7 ms. Which Nutanix technology will provide the shortest RPO possible?
A. NearSync
B. Leap
C. Metro Availability
D. AsynandDR
An administrator receives an alert in Prism indicating that interface eth2, on an AHV host is receiving many CRC errors. After togging into the problematic host, the following command is run to show the indicated output:
What is causing this issue?
A. Incorrect link speeds on the switch
B. The interface is incorrectly configured with Jumbo Frames
C. A misconfigured bond
D. A physical layer network problem
An administrator has a custom backup application that requires a 2TB disk and runs in Windows. Throughput is considerably lower than expected. The application was installed on a VM with the following configuration:
1.
Four vCPUs with one core/vCPU
2.
4GB of Memory
3.
One 50GB vDisk for the Windows installation
4.
One 2TB vDisk for the application
What is the recommended configuration change to improve throughput?
A. Increase the number of cores per vCPU
B. Increase the vCPUs assigned to the VM
C. Span the 2TB disk across four vDisks
D. Add 4GB of memory to the VM
An administrator is planning to deploy a Nutanix cluster to support a few high-performance VMs. This deployment will have the following considerations:
1.
Individual VMs will likely generate network throughputs in the range of 90-100Mbps
2.
Due to the configuration of the VMs, it is unlikely that a node will host more than one or two of them at a time
3.
Individual VMs will communicate with only a few (one or two) remote hosts at a time
4.
Multicast will not be used in the environment
5.
The hosts are connected via two 1GbE network connections
How should the administrator configure the network bonds to meet this requirement while maintaining the simplest switch configuration?
A. Configure bond0 as balance-sib
B. Configure bond0 as active-backup
C. Configure bond0 as balance-tcp
D. Configure bond0 as balance-lacp