JN0-363 Online Practice Questions and Answers

Which new field is added to an IPv6 header as compared lo IPv4?

A. version

B. checksum

C. fragment offset

D. flow label

Exhibit Referring to the exhibit, which two statements are correct? (Choose two.)

A. The OSPF Interfaces are configured as point-to-point.

B. The ge-0/0'1.0 Interface is configured as passive.

C. The R2 device is an ABR.

D. Junos OS default OSPF hello timers and dead intervals are used on all interfaces.

Exhibit

You configured interface ge-0/070.0 to run IS-IS. but this interface does not appear in the output of the show isis adjacency command as shown in the exhibit.

What is the problem in this scenario?

A. This is a Gigabit Ethernet interface, that is incompatible with the reference-bandwidth 100g statement.

B. The family iso statement must be added to the logical interface.

C. The router at the other end of the link Is not sending any IS-IS Hello messages.

D. The router at the other end of the link is a Level 1 only router.

Exhibit

Referring to the exhibit, which two statements are correct? (Choose two.)

A. Traffic ingressing ge-0/0/0 that is tagged with VLAN 101 will egress ge-0/0/1 unchanged.

B. Traffic ingressing ge-0/0/0 that is tagged will VLAN 100 will be dropped.

C. Traffic ingressing ge0/0/0 that Is tagged with VLAN 200 will egress ge-0/0/1 with an outer VLAN tag of 200.

D. Traffic ingressing ge-0/0/0 that is tagged with VLAN 101 will egress ge-0/0M with an outer VLAN tag of 200.

You are adding an IPv6 configuration to an Interface on a Junos device.

In this scenario, which statement is correct?

A. The link local address must be manually configured within the fdO0::/8 prefix range.

B. The link local address must be manually configured within the fe80::/10 prefix range.

C. The link local address is automatically created using the MAC address within the fe80::'l0 prefix range.

D. The link local address is automatically created using the MAC address within the fd00::/8 prefix range.

Exhibit

You are asked to configure OSPF between routers R1 and R2 using IPv6 addresses. Which two tasks will accomplish your objective? (Choose two.)

A. Issue the sec protocols ospf area 0.0.0.0 interface ge-0/0/1.0 command.

B. Under the [edit routing-options] hierarchy, configure a 32-bit router ID.

C. issue the set protocols ospf3 area 0.0.0.0 interface ge-0/0/1.0 command.

D. Under the [edit routing-options] hierarchy, configure a 128-bit router ID.

Exhibit

Referring to the exhibit, how do you verify the status of the tunnel from R1?

A. Issue the ping 172.20.111.10 source 172.20.110.1 command.

B. Issue the ping 172.20.111.10 source 198.51.100.1 command.

C. Issue the ping 172.20.iii.io source 203.0.113.2 command.

D. Issue the ping 172.20. Ill. 10 command.

What are two types of SlDs used in segment touting? (Choose two.)

A. node

B. adjacency

C. link

D. interface

Which two statements are correct about the way that BGP propagates routes by default? (Choose two.)

A. A route learned by EBGP will be re-advertised to IBGP peers.

B. A route learned by IBGP will not be re-advertised lo IBGP peers.

C. A route learned by EBGP will not be re-advertised to IBGP peers.

D. A route learned by IBGP will be re-advertised to IBGP peers.

Which LSA type does an OSPF ABR use to advertise external routes generated by an NSSAASBR into the backbone?

A. Type 5

B. Type 7

C. Type 3

D. Type 1