HPE6-A72 Online Practice Questions and Answers

DRAG DROP

Match each description to the correct management tool for Aruba AOS-CX.

Select and Place:

DRAG DROP

Place the OSI Layers in the correct order. Arrange them from least to greatest, starting with Layer 1 on the top, and progressing to Layer 7 on the bottom.

Select and Place:

ServiceOS login: admin

SVOS> password

Enter password: ********

Confirm password: ********

The login password to access an Aruba AOS-CX was lost. After connecting to the switch console port, a reboot is performed and the Service OS console is accessed as shown above.

What is the default password that is required for the admin account while under the Service OS console?

A. No password is set for this account.

B. "password"

C. "forgetme!"

D. The same login password that has lost originally.

What is a benefit of choosing a 3-Tier design with routing at the Aggregation layer?

A. Better Core router performance by offloading processing

B. Shifting endpoint access to the Aggregation layer from the Access layer

C. Using access control lists (ACLs) at the Core to improve performance

D. Connecting WAN/MPLS and Data center access to the Aggregation layer

Refer to the exhibit.

You are in the process of configuring VSF between Access-1 and Access-2. Access-1 has been configured as the VSF Master.

What is a valid configuration for Access-2 to join the VSF stack?

A. Access-2# configure Access-2(config)# vsf member 1 Access-2(config)# vsf renumber-to 2 Access-2(vsf-member-1)# link 2 2/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

B. Access-2# configure Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 2 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

C. Access-2# configure Access-2(config)# vsf member 2 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

D. Access-2# configure Access-2(config)# vsf member 1 Access-2(vsf-member-1)# link 1 1/1/28 Access-2(vsf-member-1)# exit Access-2(config)# vsf renumber-to 2 This will save the VSF configuration and reboot the switch. Do you want to continue (y/n)? y

You have completed a successful VSF stack between two switches.

Without manually assigning a backup switch, what is the expected output when issuing a show vsf command?

A. Option A

B. Option B

C. Option C

D. Option D

What are two methods for remotely managing an Aruba AOS-CX switch? (Choose two.)

A. SNMPv2c

B. HTTPS

C. USB-C console

D. Telnet

E. SSH

Refer to the exhibit.

What commands will successfully enable the SVI for vlan 100 on interface 1/1/1 to produce the results displayed in the command show ip interface brief in the exhibit below?

A. Access-1(config)# interface 1/1/1Access-1(config-if)# routingAccess-1(config-if)# interface vlan 100Access-1(config-if-vlan)# ip address 10.1.1.1/24

B. Access-1(config)# interface 1/1/1Access-1(config-if)# vlan trunk permit vlan 100Access-1(config-if)# interface vlan 100Access-1(config-if-vlan)# ip address static 10.1.1.1/24

C. Access-1(config)# interface vlan 100Access-1(config-if-vlan)# ip address 10.1.1.1/24

D. Access-1(config-if)# vlan 100Access-1(config-vlan)# ip address 10.1.1.1/24

You need to remote into an AOS-CX switch using SSH in order to update the management IP address for future connections. Unfortunately, you mis-configured the IP address and are now locked out of the switch.

What command could you have issued before making changes that would have recovered the original switch configuration after ten minutes?

A. checkpoint rollback 10

B. checkpoint auto 10

C. checkpoint auto confirm 10

D. boot system secondary 10

Refer to the exhibit.

What is the correct binary conversion of the last two hexadecimal characters of the physical address?

A. 1101 1000

B. 1110 1101

C. 1001 1111 0101 0011

D. 1000 1101 1110 1101