HPE6-A66 Online Practice Questions and Answers

Which must you perform in IRIS to assign a device to a Design Group?

A. Right-click the device and select Set Layer Membership

B. Right-click the device and select Set Design Group

C. Drag and drop the device into the Site

D. Drag and drop the device into the Design Group

A network architect is designing a wireless solution for a company that is leasing one floor in a multi- floor building in a downtown area. The customer is concerned about ensuring complete Wi-Fi coverage and pin-pointing RF hazards.

What type of survey should the network architect perform?

A. Active

B. Virtual

C. Passive

D. Spectrum clearing

A wiring closet with a POE+ switch is 250 feet (76 meters) away from an AP on a building floor. The AP's smart-rate port is connected to a smart-rate port on the switch, which is capable of 10 Gbps. The cable type is Cat5e STP.

What is the maximum speed that the customer can expect from the connected AP?

A. 2.5 Gbps

B. 1 Gbps

C. 5 Gbps

D. 10 Gbps

A network architect is given the task to design a new network solution for NewStellar Company, Inc. NewSteiiar has a main corporate campus in a business park with two adjacent buildings. The network architect has given one floor to analyze, Building 1 Floor 2, shown in the attached exhibit.

Each building has three floors and each floor is 322 x 175 feet (98 x 53 meters) for 56,350 square feet (5,235 square meters) total, which results in a total of 338,100 feet (31,410 square meters) for the entire building space. Each floor has a

central main corridor with washrooms, stairs, elevators and supply and network cabinets. There are cubicles around the perimeter of the floor. The central part main corridor's dimensions contain 9,350 square feet {870 square meters).

Because of security concerns, video cameras will be installed throughout the facility. There are 16 of these per floor, 8 per wiring closet. The cameras are non-WiFi capable and require POE 802.3af- capable switch ports from which to draw

power.

A wireless capacity design is required. Assuming that wireless coverage is required across the Building 1, Floor 2, including the central area, and that half the required APs will connect to each wiring closet, approximately how many POE+

ports will be required per wiring closet for all devices that have POE or POE+ needs?

A. 30

B. 22

C. 42

D. 8

Refer to the exhibit.

When planning the use of Cat7 cabling for a SmartRate connection between an ArubaOS AP and an ArubaOS switch, which sections should be considered when calculating distance?

A. A + C

B. A + B

C. A + B + C + D

D. A + B + C

A network architect has created two sites in IRIS and defined network devices for each site. From which window would a network architect connect the two sites together?

A. Topology

B. Site-1

C. Catalog

D. Start Page

A customer has a need to track traffic patterns and anomalies on a pair of ArubaOS-CX 8400 series switches. Which technology will the customer need to deploy for these switches?

A. Mobility First

B. NetEdit

C. Network Analysis Engine

D. 2 CiearPass

A network architect is designing a new Wi-Fi solution for a small university The solution will involve two mobility controllers that will be clustered at the campus core Because students use a lot of video in both the dormitory rooms and in the classrooms, the solution will need to support 50Gbps via link aggregation between the controllers and core switches. Which solution would most cost-effectively meet this requirement for the campus core?

A. Aruba 7220 mobility controllers and 3810M switches

B. Aruba 7210 mobility controllers and 5406R switches

C. Aruba 7240XM mobility controllers and 3810M switches

D. Aruba 7280 mobility controllers and 5406R switches

A network architect is replacing an old wireless implementation based on 802.11 a with a new wireless solution. The company has a lot of money invested in legacy wireless barcode scanners and will not be replacing them. However, the bandwidth that the company expects each AP to have less than 700 Mbps in bandwidth, and this is not expected to change in the future. Which wireless solution would best meet this company's needs and be the most cost-effective?

A. 802.11n

B. 802.11ax

C. 802.11g

D. 802.11ac

A network architect needs to design a new wireless solution for a small company The architect estimates that about 150 APs will be required to implement a capacity design. Roaming support is required. Also, the design requires meshing to connect some of the APs to the network. The customer requires that client state synchronization be provided for real-time failover. Which solution would most cost-effectively meet these requirements?

A. lAPs in a cluster

B. FRAPs in a cluster

C. Two 7205 mobility controller and campus APs in a cluster

D. Two 7030 mobility controller and campus APs in a cluster