HP0-Y52 Online Practice Questions and Answers

A network administrator needs to restrict access to the console port of an HPE Comware switch. When a user connects to the console port and opens a terminal session, the switch should prompt the user for a password. How should the administrator configure user interfaces on the Comware switch?

A. Set the authentication mode to password on the VTY 0 15 interfaces and then set the password on the VTY 0 15 interfaces.

B. Set the authentication mode to scheme on the VTY 0 15 interfaces and then set the password globally.

C. Set the authentication mode to password on the AUX 0 interface and then set the password on the AUX 0 interface.

D. Set the authentication mode to scheme on the AUX 0 interface and then set the password globally.

What does the traceroute command identify on an HP ProVision switch?

A. each Layer 3 device between the switch and a destination

B. the path to each router connected to the switch

C. debug output tracing entries to the routing table

D. each physical device between the switch and a destination

Refer to the exhibit.

Examine the partial HP switch output shown in the exhibit. Based on this output, if the switch receives a packet with a destination IP address of 10.2.90.87, which entry in the routing table would the switch use to forward the packet?

A. 10.2.128.0/17

B. 10.2.0.0/17

C. 10.2.64.0/19

D. 10.2.64.0/18

Which FlexNetwork architecture component provides high performance and low-latency for virtual and physical servers that provide services to the users in a company?

A. FlexFabric

B. FlexDataCenter

C. FlexNet

D. FlexArchitecture

Which HP device or port type can modify, read, and respond with frames that include 802.1Q VLAN tags?

A. Comwaretrunk ports

B. Comwareroute-mode ports

C. ProVisionloopback ports

D. ProVisionuntagged ports

Refer to the Exhibit. Exhibit: HP Comware switch configuration. [Comware] vlan 100 [Comware-vlan100] quit [Comware] vlan 200 [Comware-vlan200] quit [Comware] interface g1/0/22 [Comware-GigabitEthernet1/0/22] port link-type trunk [Comware-GigabitEthernet1/0/22] port trunk permit vlan 100 200 [Comware-GigabitEthernet1/0/22] quit A network administrator configures the Comware switch, as shown in the exhibit. The network administrator then connects a cable from the Comware's g1/0/22 interface to port 5 on an HP ProVision switch. Which configuration will

successfully establish connection for VLAN 1, 100, and 200 between the two switches?

A. ProVision (config) # vlan 100ProVision (config) # vlan 200ProVision (config) # vlan 100 tagged 5ProVision (config) # vlan 200 tagged 5

B. ProVision (config) # vlan 100ProVision (config) # vlan 200ProVision (config) # interface 5 tagged 100 200

C. ProVision (config) # vlan 100ProVision (config) # vlan 200ProVision (config) # interface 5 tagged 100ProVision (config) # interface 5 tagged 200

D. ProVision (config) # vlan 100 200ProVision (config) # vlan 100 200 tagged 5

A network administrator plans to execute show commands as well as make conjuration changes. Which HP ProVision privilege role must be assigned to an account for the administrator to do this?

A. Operator

B. Administrator

C. Superuser

D. Manager

Refer to the exhibit.

Based on the output shown in this exhibit, which statement is true about the 10.0.0.2 neighbor?

A. The neighbor is communicating with this switch, but it cannot hold any more routes in its database.

B. The neighbor is communicating with this switch, and they have exchanged all topology information.

C. The neighbor has mismatched settings and cannot exchange information with this switch.

D. The neighbor is rejecting communications because it already has its maximum number of neighbors.

Refer to the exhibit.

An HP Comware switch is using its default user-interface settings. The network administrator then enters the commands shown in the exhibit. What correctly describes how an admin user must now log in?

A. When the admin user logs in to the console port, the admin user must enter either a password of password1 or password2.

B. When the admin user logs in using Telnet, the admin user must enter either a password of password1 or password2.

C. When the admin logs in using Telnet, the admin user must enter a password of password1 and is given level 1 privileges.

D. When the admin user logs in to the console port, the admin user must enter a password of password1 and is given level 3 privileges.

Refer to the exhibit.

The topology shown in this exhibit implements Multiple Spanning Tree Protocol (MSTP), where all the switches are in the same region.

How many MSTP instances, besides the Internal Spanning Tree (IST) or instance 0, does this network need in order to have effective load sharing on the uplinks from the access switches?

A. two

B. three

C. four

D. five