C9010-022 Online Practice Questions and Answers

A system dump has been initiated on an LPAR and LED code "0c1" is displayed, indicating an I/O error. Where can the administrator find out more about this error?

A. The HMC Service Guide

B. The AIX Version 7.1 Commands Reference

C. HMC Event Log

D. IBM's Fix Central under Power Systems LED support page

What option will boot an LPAR directly from DVD media, without any user interaction required, when starting the LPAR from the Hardware Management Console (HMC)?

A. Normal

B. Diagnostic with default boot list

C. System management services

D. Open firmware OK prompt

Name resolution is not working on a given LPAR. Considering the observed behavior and configuration of/etc/resolv.conf, what is the most likely resolution?

A. Correct the definition of nameserver1.

B. Remove the domain line.

C. Verify the syntax in /etc/nelsvc.conf.

D. Move the search definition to the beginning of the file

An administrator wants to create a filesystem with a specific logical volume name, disk location, and disk placement. Which pair of commandswill allow these attributes to be set during filesystem creation?

A. crfs followed by chvg

B. crlv followed by mkfs

C. mkfs followed by chfs

D. mklv followed by crfs

Where is Cluster Aware AIX cluster configuration data stored?

A. A shared diskthat is accessible from all nodes

B. A NFS filesystem that is accessible by all nodes

C. A shared system pool that is accessible by all nodes

D. A master copy on one node and the data is replicated to the local disk of the other nodes

An administrator needs to download and install a later version of the IBM Systems Director Common Agent. Which command would extract the contents of the installation package (SysDir6_3_2_Common_Agent_AIX.tar.gz) to a local directory?

A. unzip -l SysDir6_3_2_Common_Agent_AIX.tar.gz

B. geninstail -ue SysDir6_3_2_Common_Agent_AIX.tar.gz -d.

C. gunzip -cd SysDir6_3_2_Common_Agent_AIX.tar.gz | tar-xvf-

D. uncompress SysDir6_3_2_Common_Agent_AIX.tar.gz | installp -et

A failed integrated tape drive was physically replaced in a small P0WER7+ server. The administrator attempts to use the device and receives this error message:

AN ERROR OCCURRED WHILE WRITING TO THE STORAGE MEDIA THE DEVICE IS NOT READY FOR OPERATION

Which of the following is the most likely cause?

A. The tape device microcode needs to be updated.

B. The media inside the failed tape drive was not removed.

C. The tape drive needs to be powered on before being used.

D. The drive was replaced but the new device information was not configured

When attempting to connect to a remote system, a long delay is experienced before the login prompt is displayed. Which of the following is the most likely cause of this issue?

A. The /etc/resolv.conf file on the remote system is missing.

B. The /etc/resolv.conf file on the remote system has an invalid entry.

C. The /etc/hostsfile on the remote system does not have an entry for itself.

D. The /etc/hosts file on the remote system has an invalid hostname listed for itself.

A customer wants to restore a mksysb using a NIM server while using the least amount of disk space possible.

Which set of actions does the customer need to take?

A. Define mksysb resource, create lpp_source from mksysb resource

B. Define mksysb resource, create spot from lpp_source resource

C. Define mksysb resource, create spot from mksysb resource

D. Define spot resource, create lpp_source from mksysb resource

An LPAR is hosted on Power8 hardware.

How can an adapter assigned as "required" to that LPAR be removed with minimal downtime?

A. Initiate the Add/Remove procedure from the ASMI

B. Use the CHARM tool to remove the adapter

C. Remove the device throughdiag,and DLPAR remove the adapter

D. Remove the required setting in the profile, and DLPAR remove the adapter