6103 Online Practice Questions and Answers

After configuring your VSP 9000 for web access, engineers on the team says that they cannot log into EDM using their credentials.

What are the default credentials for EDM?

A. username: admin password: password

B. username: rwa password: rwa

C. username: admin password:

D. username: avaya password: avaya

A technician has implemented RSMLT edge design. After recovering from a power outage, some clients could not communicate. It has been determined that only one of the core RSMLT switches has recovered.

What should have been done to prevent the loss of communications?

A. Turn off the HoldDown timer.

B. RSMLT-Edge needs to be enabled globally.

C. Clear the peer IP and MAC addresses.

D. Set the VLAN to copy RSMLT info from a similarly configured VLAN.

A customer has a edge switch connected to a cluster of VSP 9000 switches. The uplinks to the network core are via two Gigabit uplink ports. The uplinks are not aggregated and are running spanning tree protocol.

The result is that one of the links is always being blocked, and recovery time is unacceptably long when the active uplink fails. They need to have both links active to increase the bandwidth to the core, and at the same time provide better redundancy. What is the preferred Avaya solution for the customer?

A. Connect both of the uplinks to one of the VSP 9000 switches and disable spanning tree.

B. Connect one uplink to each of the VSP 9000 switches to create a triangle and use spanning tree protocol.

C. Connect one uplink to each of the VSP 9000 switches to create a triangle and configure a SMLT with either MLT or LACP on the access switch. Spanning tree must be disabled.

D. Connect one uplink to each of the VSP 9000 switches to create a triangle and configure a SMLT with either MLT or LACP on the access switch. Spanning tree must be enabled.

Avaya Command Line Interface (ACLI) is an industry standard CLI that can be used to manage the Virtual Services Platform (VSP) 9000.

From within which CLI context would you enable global routing settings?

A. global configuration

B. router configuration

C. local configuration

D. interface configuration

In the current business environment everyone is being asked to do more with fewer physical resources. Using virtualization allows the Virtual Services Platform (VSP) 9000 to increase the services provided.

By using VRF-Lite, what does the VSP 9000 eliminate the need for?

A. SMLT

B. RSMLT

C. Non-overlapping addresses

D. Multiple physical routers

How do the Switch Fabric (SF) modules provide bandwidth management across the I/O modules?

A. The bandwidth management is handled by the CP modules.

B. SF modules in slots SF1 and SF4 provide bandwidth management across the I/O modules.

C. Bandwidth management is shared across all installed SF modules.

D. The SF module in slot SF1 provides bandwidth management for the I/O modules in slots 1-5, while the SF module in slot SF4 provides bandwidth management for slots 6-10.

E. The SF module in slot SF1 provides bandwidth management for even numbered slots (2,4,6,8,10), while the SF module in slot SF4 provides bandwidth management for odd numbered I/O slots (1,3,5,7,9).

Which statement about the local router MAC addresses on RSMLT aggregation switches (cluster) is true?

A. On a RSMLT aggregation switch pair, local router MAC addresses are exchanged, and only used in case of switch failure.

B. On a RSMLT aggregation switch pair, local router MAC addresses are exchanged, and always used for data forwarding.

C. On a RSMLT aggregation switch pair, the virtual MAC address is exchanged, and used for data forwarding.

D. RSMLT aggregation switches are not exchanging local router MAC addresses, but are using the IP destination address to forward traffic.

Refer to the exhibit.

Simple Loop Prevention Protocol (SLPP) provides active protection against Layer 2 network loops on a per-VLAN basis. For the SLPP Tx process, the network administrator decides on which VLANs to enable SLPP. The hello packets are then replicated out all ports that are members of the SLPP-enabled VLAN.

Given the following information shown in the exhibit: A = InterSwitch Trunk (IST) B = Split MultiLink Trunk (SMLT) # 1 VSP 9000 # 2 VSP 9000 # 3 ERS 4500

When setting up the SLPP Rx process, which configuration role is setup on VSP #1?

A. The VSP #1 Rx process is enabled on all SMLT VLANs to monitor for the ERS #3 SLPP packets.

B. The VSP #1 Rx process is enabled on port 3/1 and the IST ports to monitor for the VSP #2 SLPP packets.

C. The VSP # 1 Rx process is enabled on all SMLT VLANs to monitor for the VSP # 2 SLPP packets.

D. The VSP # 1 RX process is enabled on port 3/1 to monitor VSP # 1 and VSP #2 SLPP packets.

A campus network requirement is to introduce Virtual Routing and Forwarding (VRF) in the existing Virtual Services Platform (VSP) 9000 core. The technician needs to configure VRF on the VSP 9000.

Which statement represents the proper order for configuring a new VRF?

A. Create a new VLAN, add an IP address, create a VRF, and move the VLAN to the new VRF.

B. Create a VRF, add an IP address, create a new VLAN, and move the VLAN to the new VRF.

C. Create a VRF, create a new VLAN, add an IP address, and move the VLAN to the new VRF.

D. Create a VRF, create a new VLAN, move the VLAN to the new VRF, and add an IP address.

Given the following command:

VSP-9012:1S show khi performance

Which Key Health Indicator is only valid for the CP modules?

A. CPU

B. buffer-pool

C. error-count

D. process

E. memory