Pass4itsure > Avaya > Avaya Aura > 6002.1 > 6002.1 Online Practice Questions and Answers

6002.1 Online Practice Questions and Answers

Questions 4

A technician is planning to support to upgrade an Avaya communication Manager system to release 6.0 from Release 5.2

Which two tasks must be performed during the upgrade procedure? (Choose two)

A. The S8700-series servers must be displayed by S8800 servers.

B. All G350 gateways must replaced by S8800 servers.

C. The survivable remote servers must be upgraded by Release 6.0

D. The survivable Remote servers can stay at Release 5.2

Buy Now
Questions 5

When using the Avaya Site administrator CEDI interface, which command would be used to check the configuration of telephone set with the extension of 1000?

A. Print station 1000

B. Display station 1000

C. Show station 1000

D. View station 1000

Buy Now
Questions 6

To confirm that a survivable server is currently registered to the main CM servers, using the SAT. Which command should be entered

A. Status ess clusters

B. Display survivable-processors

C. Status ess port-networks

D. Status survivable-processors

Buy Now
Questions 7

Which procedure must be followed while, migrating from CM 5.2.1 (S8800 Server with 2 HDD) to CM 6.0?

A. Insert 3rd hard drive, run raid CD, and than run raid CD after rebooting.

B. Take backup, store the backup locally, insert 3rd hard drive, and then run Raid CD after rebooting.

C. Insert the raid CD, reboot the server, and than take backup.

D. Insert the hard drive and the 3rd hard drive is incorporated automatically.

Buy Now
Questions 8

When using the Avaya Site Administration GSDI interface, which command would be use to built a new telephone set with the extension of 1000?

A. New station 1000

B. Add station 1000

C. Build station 1000

D. Add set 1000

Buy Now
Questions 9

Which MAC address is recommended for the license file?

A. The MAC address of the Console domain

B. The MAC address of the CM eth0 port

C. The MAC address of the CM host name

D. The MAC address of the DOM0

Buy Now
Questions 10

A newly installed main Cm 6.0 server indicates it is in license error mode. A technician again 45 minutes later and it is still in error mode. The license was installed from the system management interface (SMI)?

Which statement describes the reason for the error mode?

A. The installer used the wrong interface to install the license and it is therefore not installed.

B. The server cannot communicate with the IPSI or media gateway whose serial number was used in the license file.

C. The license audit runs every 60 minutes and the error will be resolved in 15 minutes.

D. The installer loaded a license for one of the survivable servers, not the main server, and the IPSIs, media Gateways, and/or IP phones have registered to it

Buy Now
Questions 11

What two pieces of information does the product licensing and delivery system (PLDS) required to be entered for a license file to be generated? (Choose two)

A. Serial number

B. License activation code

C. MAC address

D. Platform type

Buy Now
Questions 12

A customer has a communication Manager R6.0 system with IP phones and some older TDM phone, and says there is no dial tone for all of the IP phones. All of the hardware has been verified to be working properly.

Which two steps can be taken to identify the cause of problem? (Choose two)]

A. Verify that the TN2602 Media resources circuit pack has the correct IP settings.

B. Verify that the processor Ethernet mode is enabled in the Server.

C. Set a static IP address on a laptop and see if the server can be pined

D. Set a static IP address on a laptop and see if the TN2602 Media Resource circuit pack can be pinged.

Buy Now
Questions 13

Which statement describes how the communication message application is enabled the first time after the installation?

A. Connect the SAT terminal login using the craft, and then enable using the enable messaging command.

B. Open the communication manager IP address using web browser. Login as craft, click installation, than communication manager messaging.

C. Open the communication manager IP address using web browser. Login as craft; click Administration, then server (maintenance), than click miscellaneous, than messaging software, and than click enable.

D. Communication manager messaging is enabled by default after the installation.

Buy Now
Exam Code: 6002.1
Exam Name: Avaya Aura(TM) Communication Manager and CM Messaging (R6.0) Implementation Exam
Last Update: Apr 13, 2024
Questions: 69
10%OFF Coupon Code: SAVE10

PDF (Q&A)

$45.99

VCE

$49.99

PDF + VCE

$59.99