5V0-41.20 Online Practice Questions and Answers

Scenario 3:

After resolving numerous connectivity issues throughout the various branch sites, connectivity between applications and users is finally present. The network administrator is informed that during certain tests, applications are not performing as they are expected to. Users report that call quality has not fully improved and that some of their calls either drop or have poor voice quality where the conversation is breaking up. Other users are noticing that file transfers are slower than expect. A group of users from a few sites have reported slowness in accessing internal and external applications.

Exhibit.

A network engineer is configuring an Internet Backhaul Policy for the Chicago Branch to utilize NY's hub as a much better source for Internet for certain SaaS applications. For an unknown reason, the network engineer is not able to select the hubs in the Internet Backhaul Policy.

What could be the reason?

A. The Dynamic Branch to Branch has not been enabled.

B. The hub is not configured with the proper IP address.

C. Dynamic Branch to Branch using gateways has not been enabled.

D. The Edge's profile does not include Backhaul hubs as an option.

Scenario 3:

After resolving numerous connectivity issues throughout the various branch sites, connectivity between applications and users is finally present. The network administrator is informed that during certain tests, applications are not performing as they are expected to. Users report that call quality has not fully improved and that some of their calls either drop or have poor voice quality where the conversation is breaking up. Other users are noticing that file transfers are slower than expect. A group of users from a few sites have reported slowness in accessing; internal and external applications.

Exhibit.

A network administrator is configuring several branches to prefer a single prefix, 10.20.11.0/24, from the Seattle hub over the New York hub for various application performance reasons.

What are two effective ways the administrator can accomplish this? (Choose two.)

A. Modify the AS Path in New York to be shorter for 10.20.11.0/24.

B. In the hub preferred order in the profile, set the Seattle hub to be preferred over New York.

C. Modify the AS Path in New York to be longer for 10.20.11.0/24.

D. In the OFC 10.20.11.0/24, modify the preferred exit point to be Seattle and pin the route.

Scenario 2:

After completing the branch activation activities for all required branches, the administrator attempts to test connectivity between the various branches and between the hubs and branches- The administrator notices a lack of connectivity despite being certain that configurations have been complete. The administrator also observed that several users are reporting intermittent connectivity to some of the applications they are accessing. Other users are reporting no access to these applications. Other users at some of the branches claim they cannot get to certain public resources. The administrator wants to ensure that all sites can talk to each other and all resources are accessible.

Exhibit.

The tunnel from the Dallas site to the Seattle hub is not coming up.

What are two things that should be checked to determine the issue? (Choose two.)

A. Hub WAN Interface might be behind a firewall.

B. Spoke Edge and Hub Edge have a mismatched certificate.

C. Dynamic Branch to Branch is not enabled.

D. Spoke Edge and Hub Edge are two different Edge models.

Scenario 3:

After resolving numerous connectivity issues throughout the various branch sites, connectivity between applications and users is finally present. The network administrator is informed that during certain tests, applications are not performing as they are expected to. Users report that call quality has not fully improved and that some of their calls either drop or have poor voice quality where the conversation is breaking up. Other users are noticing that file transfers are slower than expect. A group of users from a few sites have reported slowness in accessing internal and external applications.

Exhibit.

A network administrator is receiving complaints that a real-time voice application is not performing well, with choppy audio, and dead audio especially during peak traffic times.

What two actions can the administrator take to diagnose and fix the issue? (Choose two.)

A. Configure a QoS policy to rate limit all traffic during peak times.

B. Ensure that the realtime application is matching the correct application type using the diagnostics page.

C. Check the status of the links using the QoE and Transport tabs for any degraded underlay issues or congestion issues.

D. Configure a QoS policy to load balance the realtime traffic across all links.

Scenario 1:

The Dallas Branch location is having issues getting activated. The local network administrator is aware that the Edge device received a DHCP address and was able to connect to the internet. The Orchestrator is reporting the Edge as Down. No other changes were made post activation.

A network administrator is tasked with enabling SD-WAN at three branch locations. A topology has been provided for reference. For each site, the administrator is having issues bringing edges

online, as another administrator has gone ahead and created a configuration ahead of time. The organization has several branch sites. One is am Internet-only site and two are Hybrid locations with both internet and MPLS. The last location is MPLS only. There are hub data center locations in this environment as well. Please refer to the topology.

Refer to the Exhibit(s).

What is the cause of this issue?

A. The activation link did not specify the updated image location requiring the Edge to be re-activated.

B. The activation link did not contain any post-activation configuration to allow the Orchestrator to communicate with the Edge.

C. The Edge will be offline for about 4 hours until it has completed the factory image installation.

D. The activation link contained incorrect configurations for WAN overlays and WAN interfaces.

Scenario 3:

After completing the branch activation activities for all required branches, the network administrator attempts to test connectivity between the various branches and between the hubs and branches. The administrator notices a lack of connectivity despite being certain that configurations have been complete. The administrator also observed that several users are reporting intermittent connectivity to some of the applications they are accessing. Other users are reporting no access to these applications. Other users at some of the branches claim they cannot get to certain public resources. The administrator wants to ensure that all sites can talk to each other and all resources are accessible.

Exhibit.

The network administrator determines that dynamic routes to SD-WAN sites are missing at the San Jose branch router. The network administrator decides to look into the configurations of hub Edges. All SD-WAN branch sites must use a hub to communicate with the San Jose site. Best practices have been implemented at these SD-WAN sites.

Where should the administrator check first to verify if the configuration is correct?

A. Verify that the NVS feature is enabled in Cloud VPN.

B. Verify that redistribution between the primary hub site and San Jose is enabled.

C. Verify the static routes to San Jose from all Branches are configured.

D. Verify that redistribution at the Dallas Hybrid Site is enabled for San Jose to use as a peering point.

Scenario 3:

After resolving numerous connectivity Issues throughout the various branch sites, connectivity between applications and users is finally present- The network administrator is informed (hat during certain tests, applications are not performing as they are expected to. Users report that call quality has not fully improved and that some of their calls either drop or have poor voice quality where the conversation is breaking up. Other users are noticing that file transfers are slower than expect. A group of users from a few sites have reported slowness in accessing internal and external applications.

Exhibit.

Which metrics can a network administrator verify in the QoE screen to determine the overall health of Underlay and Overlay?

A. Jitter Packet Loss, Speed.

B. Jitter, Packet Loss, Latency.

C. Jitter, Speed, Latency.

D. Packet Loss, Latency, Speed.

Scenario 2:

After completing the branch activation activities for all required branches, the network administrator attempts to test connectivity between the various branches and between the hubs and branches. The administrator notices a lack of connectivity despite being certain that configurations have been complete. The administrator also observed that several users are reporting intermittent connectivity to some of the applications they are accessing. Other users are reporting no access to these applications. Other users at some of the branches claim they cannot gel to certain public resources. The administrator wants to ensure that all sites can talk to each other and all resources are accessible.

Exhibit.

A business policy is created and saved.

How can the network administrator verify the business policy is working?

A. Select a VCE > Test and Troubleshoot > Remote diagnostics and select List Active flows and check the flows to see what Business policy is applied under the Business policy column.

B. Executing Route table dump under VCE > Test St Troubleshoot > Remote Diagnostics and select Route Table dump and look for business policy applied in the Route table Dump stats.

C. Check under Monitor > Applications tab and check the listing of applications at the bottom of the screen and the category of the type of traffic there.

D. Check under the Monitor > Business Priority tab for Business policy statistics.

Scenario 2:

After completing the branch activation activities for all required branches, the network administrator attempts to test connectivity between the various branches and between the hubs and branches. The administrator notices a lack of connectivity despite being certain that configurations have been complete. The administrator also observed that several users are reporting intermittent connectivity to some of the applications they are accessing. Other users are reporting no access to these applications. Other users at some of the branches claim they cannot get to certain public resources. The administrator wants to ensure that all sites can talk to each other and all resources are accessible.

Exhibit.

A network administrator is trying to create multiple overlays on a single physical interface on an Edge. The administrator is able to bring up only a single overlay so far, but is having trouble with bringing up additional overlays.

What could be the possible reason?

A. The administrator does not have the right permission to create multiple overlays. The administrator needs to have an Operator-level privilege for this task.

B. On the WAN overlay configuration, verify the IP address, next-hop, and the VLAN ID configuration.

C. The licensing does not support multiple overlays on a single physical interface.

D. Multiple overlays cannot be created on a single physical interface. Multiple physical interfaces are needed.

Scenario 2:

After completing the branch activation activities for all required branches, the network administrator attempts to test connectivity between the various branches and between the hubs and branches. The administrator notices a lack of connectivity despite being certain that configurations have been complete. The administrator also observed that several users are reporting intermittent connectivity to some of the applications they are accessing. Other users are reporting no access to these applications. Other users at some of the branches claim they cannot get to certain public resources. The administrator wants to ensure that all sites can talk to each other and all resources are accessible.

Exhibit.

Where can the network administrator check to see what routes are present on the London- site Edge?

A. Log into the VCO > Configuration > Overlay Flow Control

B. Log into the VCO > Test and Troubleshoot > Remote Diagnostics > Run "List Paths"

C. Log into the VCO > Test and Troubleshoot > Remote Diagnostics > Run "Route Table Dump"

D. Log into the VCO > Monitoring > Overlay Flow Control