301A Online Practice Questions and Answers

Which Standard Virtual Server settings should an LTM Specialist use to load balance across routed path of two different ISPs?

A. address translation enabled and port translation disabled

B. both address and port translation enabled

C. both address and port translation disabled

D. address translation disabled and port translation enabled

set payload {CACHE :: payload}

}

Which two profiles should be used on the virtual server? (Choose two.)

A. http-transparent

B. http compression

C. http

D. webacceleration

E. stream

A VCMP guest has the following characteristics:

1.

Resources allocated for CPU memory, network interfaces, and disk space

2.

Virtual disk created

3.

The guest is NOT running

The guest is NOT running in which state is the VCMP guest

A. Offline

B. Deployed

C. Provisioned

D. Configured

An LTM Specialist needs to provide statistics regarding the round-trip time between the clients and the

servers.

Which metric should be part of the analytics profile to provide that information?

A. Page Load Time

B. User Sessions

C. Max TPS and Throughout

D. Response Codes

An SSL application is being migrated to the LTM device. Both encrypted and unencrypted traffic are accepted by the server. The virtual server configuration is as follows:

Which LTM device profile should be used on the LTM device to reduce the CPU load on the current.

A. Protocol

B. serverssl

C. clientsssl

D. stream

Refer to the exhibit.

An LTM Specialist configures the two syslog destination Syslog destination #1 can receive messages but

the syslog destination #2 can NOT receive messages.

Which command sill correct the issue?

A. {/Common)(tmos) # modify /syssyslog remote-servers modify (syslog_dest2 {local-ip

B. {/Common)(tmos) # modify Ays syslog remote servers modify {syslog_dest2 {local- ip 10.208.102 254)}

C. {/Common) (tmos) # modify /sys syslog remote-servers modify {syslog_dest2 {host 10 208.102.254 }}

D. {Common(tmos) # modify/syslog remote-servers modify {syslog_dest2 {lost.10.10.10.28 }}

An LTM specialist needs to upgrade a VCMP quest in an HA Setup with minimum interruption for all VCMP

guest instances.

In which should the LTM Specialist perform this upgrade?

A. Relicense the host. Failover all guest's active traffic-groups to the other host, copy image to gest, create guest UCS install and set boot location to new volume, reboot

B. Failover this specific guest's active traffic-group to the other Host, Relicense the guest, copy image to guest , create guest UCS, install and set boot location to new volume, reboot

C. Failover all guests' active traffic-group to the other Host, Relicense the host, copy image to guest, create guest UCS, install and set boot location to new volume , reboot

D. Failover all guests' active traffic-group to the other host, copy image to guest, create guest UCS install and set boot location to new volume, reboot, Relicense the host

Where does a LTM Specialist view all of the objects that are part of a deployed iApp?

A. iAPP> Application Policy > Objects

B. Local Traffic . Virtual Servers > Applications

C. IAP > Application Service > Components

D. Local Traffic > Network Map > View Map

Six servers have a varying number of connections that change based on the user load. Which load balancing method should an LTM Specialist apply to divided the web application traffic to the servers on the relative performance trend?

A. Least Sessions

B. Least Connections

C. Predictive

D. Ratio

Two LTM devices must be manually configured to restrict in the same Device Group. What is the correct order of steps to meet this requirement?

A. Configure VLAN, Configure-Sync IP, Configure Failover type, Establish Device Trust, Sync Device Trust, Create type, Establish Device Sync Device Trust, Create Device Group.

B. Configure VLAN, Configure Self-IPs, Configure Config-Sync IP. Configure Failover type, Establish Device Trust, Sync Device Trust, Create Device Group.

C. Configure Self-IPs, Configure VLAN, Configure Config-Sync IP. Configure Failover type, Establish Device Trust, Sync Device Trust, Create Device Group

D. Configure VLAN, Configure Config-Sync IP. Configure Self-IPs. Configure Failover type. Establish Device Trust, Create Device Group