Pass4itsure > Cisco > Cisco Industrial Networking Specialist > 200-401 > 200-401 Online Practice Questions and Answers

200-401 Online Practice Questions and Answers

Questions 4

DRAG DROP

Select and Place:

Select and Place:

Buy Now
Questions 5

Exhibit:

Refer to the exhibit. Which port should a PLC with IP address 192.168.3.65 be plugged into in order to communicate to the rest of the network?

A. FastEthernet1/1

B. FastEthernet1/2

C. FastEthernet1/3

D. FastEthernet1/4

E. FastEthernet1/5

Buy Now
Questions 6

Which option allows an EtherNet/IP I/O device to be safely installed where it is subject to water immersion?

A. The device is rated IP20 and the power wiring is installed securely to the terminal block.

B. The device is rated IP67 and a power cordset is used.

C. The device is rated IP67 and immersed to 10 m.

D. The device is rated IP20 and immersed to 10 m.

Buy Now
Questions 7

Exhibit: Refer to the exhibit. What are three traffic and interconnection requirements for the devices in the exhibit? (Choose three.)

A. The EtherNet/IP drive connections are in a high-voltage area and need protection from electromagnetic noise, so shielded cable that is rated for 600 V is advised.

B. EtherNet/IP devices such as the controller, drive, VoIP phone, and IP camera should be in the same VLAN.

C. CIP traffic has the highest bandwidth requirement so it needs the highest QoS setting.

D. EtherNet/IP drive traffic has high sensitivity to random drops, latency, and jitter.

E. Real-time motion control and VoIP traffic can share the same VLAN with the proper QoS setting.

F. IEEE1588 and PTP are important for ensuring real-time synchronization.

Buy Now
Questions 8

EtherNet/IP is an Ethernet implementation of which protocol?

A. CIP

B. Industrial Protocol

C. DeviceNet

D. ControlNet

Buy Now
Questions 9

Which option best describes a mechanical, ingress, climatic, chemical and electromagnetic environment that is classified as M3 I3 C3 E3?

A. the highest quality

B. office environment

C. severe

D. serviced by multiple cable segments

Buy Now
Questions 10

Exhibit:

Refer to the exhibit. The output that is shown is generated at an industrial switch. Which three statements are true? (Choose three.)

A. All ports will be in a state of discarding, learning, or forwarding.

B. Thirty VLANs have been configured on this switch.

C. The bridge priority is lower than the default value for spanning tree.

D. All interfaces that are shown are on shared media.

E. All designated ports are in a forwarding state.

F. This switch must be the root bridge for all VLANs on this switch.

Buy Now
Questions 11

What does the Cisco PSIRT issue for significant security issues that directly involve Cisco products and require an upgrade, fix, or other customer action?

A. Cisco Security Advisories

B. Cisco Security Responses

C. Cisco Security Notices

D. Cisco Security Bulletins

Buy Now
Questions 12

Exhibit: Refer to the exhibit. A technician enters the exhibited commands to configure a new router on the plant floor, but receives an error message when attempting to save the configuration. What can the technician do to correct the problem?

A. Enter the correct command.

B. Enter the command at the correct prompt.

C. Upgrade the amount of flash memory in the router.

D. Erase NVRAM to make room for the configuration file.

E. Add NVRAM because there is not enough room for the configuration file.

Buy Now
Questions 13

What is the purpose of a time domain reflectometer?

A. It uses pulses to locate and test for sheath faults, damaged conductors, loose connectors, splices, bridge taps, split pairs, and other problems.

B. It opens shorts and pinholes in cable shielding.

C. It correlates the returned light pulses with a location in the fiber.

D. It opens kinks and mismatched cable connectors.

Buy Now
Exam Code: 200-401
Exam Name: Managing Industrial Networks with Cisco Networking Technologies (IMINS)
Last Update: Jul 02, 2023
Questions: 64
10%OFF Coupon Code: SAVE10

PDF (Q&A)

$45.99

VCE

$49.99

PDF + VCE

$59.99